| Description: |
- Optical Register Sheet Infeed System ORSIS (Optical Register Sheet Infeed synchronisation).- Platen with camshaft drive.- Machine compatible with HIGHWAY TDF-VIEW system.- Centreline system for fast job changes.- Electronic sheet flow control.- Adjustable centring on the stripper.- Control cabinet air conditioning.- Several automated functions to assist the machine operator including- Controlled machine stop after system error (allows the sheets in the machine without interruption).- Feeding of a sheet from the feeder into the stripping station for control of the die-cutting / creasing.- Feeding a sheet into the stripping station to check the tool position, if necessary.- Programmed stop of the machine for changing the equipment- Bobst-Electronic machine operating system C.U.B.E. ll (Control Unit Bobst Electronic) with colour screen.- Main drive by frequency-controlled asynchronous motor- The ORSIS optical infeed system includes:- Independent feeder controlled by electric shaft.- Optical side register control.- Automatic lateral stack correction (+/- 40 mm) controlled by the optical side register.- Automatic synchronisation device for optimum positioning of the sheets to the front lays.- Deceleration device with electronic control (3speeds for feeding the sheets to the front lays).- Stepless stroke of the pile support plate to maintain a constant pile height.- Adjustable side blower .- Suction head with multiple adjustment options.- Optical side register control, without sheet contact, with large correction range in both directions (+/- 10 mm).- A camera aligns the sheets laterally according to the sheet edge or the print image.- Allows the alignment of all materials (paper, solid board, laminated corrugated board).- Coated with a stainless steel sheet, with antistatic effect.- Introduction to the feed table with side ramps.- 4 x Individually adjustable front lays with sheet control during production.- Control system by fibre optics- Double sheet control without contact.- Sheet hold-down device (guiding the sheets to the grippers).- Upper feed table frame with manual lifting aid.- Upper transport equipment for paper and cardboard.- 2 x transport belts.- With lateral guide and automatic clamping system.- Movable platen with short stroke and cam drive.- Cam-controlled platen movement allows a sheet transfer with low acceleration and deceleration.- Platen with constant parallelism over the entire pressure range.- Upper platen with vacuum.- Gripper reopening device.- Automatic centring and locking of the closing frame and the base plate.- Adjustable centring for base plate (+/- 0.9 mm).- Locking of the clamping frame against the upper platen.- Measuring the punching force with tension gauge.- Motorised adjustment of the punching force.By push button.- Support plate made of synthetic material.12 mm thick.- A set of 5 x thin plates, thickness 1 mm- 1 x Upper quick-action clamping frame: screwed base plate (E-3)- Base plate, 2 mm thick, with a synthetic lashing protection plate,1 mm thick.1 x levelling plate (E-5) 4 mm thick. This ground steel plate is designed for the use of thin punching plates. Advantageous for repeat orders.- Stripping station with:- Centre drawer frame with quick clamping.- BSSR - Upper quick clamping frame.- Integrated quick-clamping device for a finished upper stripping tool.- Adjustable centring for the upper, middle and lower stripping tool.- 1 x Fixing material for the upper stripping mould for quick clampingAllows the attachment of a wood stripping mould in the upper quick clamping device- integrated upper quick-clamping device.1 x Fastening material for the stripping board on the centre frame with quick clamping1 x Lower drawer frame1 x Lower stripping equipment- Waste stripping equipment with support rods and telescopic pins.Delivery Section includes:- Pallet support plate.- Pneumatically controlled front and side straighteners.- Rear and side straighteners with centreline markings adjustable.- Continuous stack lowering with minimum/constant drop height onto the stack.- Brake brush.- Motorised, the contact pressure and angle position can be adjusted via the C.U.B.E.The mode of operation is automatic, it adapts to the machine speed.- Simple adjustment via the digital display enables the brush and the positioning of the brush and tray according to the sheet length.- Blower sheet down holder controlled by C.U.B.E.Allows accurate stacking of sheets for light grammages and paper.- Manual non-stop rake.- Photocells to check whether sheets are outside the grippers |
